收藏本站
YS05S10 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 10 A
V CTRL ? 0 . 7 ?
(5.1 1 ? R EXT )(V O - REQ - 0.7525)
30.1
[V]
cooled to a safe operating temperature, it will
automatically restart.
where,
V CTRL ? Control voltage [V]
R EXT ? External resistor between TRIM pin and
voltage source; the value can be chosen depending
on the required output voltage range [k ? ].
Control voltages with R EXT ? 0 and R EXT ? 15 K are
shown in Table 2.
Table 2: Control Voltage [VDC]
Safety Requirements
The converter meets North American and
International safety regulatory requirements per
UL60950 and EN60950. The maximum DC voltage
between any two pins is Vin under all operating
conditions. Therefore, the unit has ELV (extra low
voltage) output; it meets SELV requirements under
the condition that all input voltages are ELV.
The converter is not internally fused. To comply with
V 0-REG [V]
0.7525
1.0
V CTRL (R EXT = 0) V CTRL (R EXT = 15 K)
0.700 0.700
0.658 0.535
safety agencies’ requirements, a recognized fuse
with a maximum rating of 20 Amps must be used in
series with the input line.
1.2
1.5
1.8
2.0
2.5
3.3
3.63
0.624
0.573
0.522
0.488
0.403
0.268
0.257
0.401
0.201
-0.000
-0.133
-0.468
-1.002
-1.044
Characterization
General Information
The converter has been characterized for many
operational aspects, to include thermal derating
(maximum load current as a function of ambient
temperature and airflow) for vertical and horizontal
mountings, efficiency, startup and shutdown
Protection Features
Input Undervoltage Lockout
Input undervoltage lockout is standard with this
converter. The converter will shut down when the
input voltage drops below a pre-determined voltage;
it will start automatically when Vin returns to a
specified range.
The input voltage must be typically 2.05 V for the
converter to turn on. Once the converter has been
turned on, it will shut off when the input voltage
drops below typically 1.9 V.
Output Overcurrent Protection (OCP)
The converter is protected against overcurrent and
short circuit conditions. Upon sensing an overcurrent
condition, the converter will enter hiccup mode. Once
over-load or short circuit condition is removed, Vout
will return to nominal value.
Overtemperature Protection (OTP)
The converter will shut down under an
overtemperature condition to protect itself from
overheating caused by operation outside the thermal
derating curves, or operation in abnormal conditions
such as system fan failure. After the converter has
parameters, output ripple and noise, transient
response to load step-change, overload, and short
circuit.
The figures are numbered as Fig. x.y, where x
indicates the different output voltages, and y
associates with specific plots (y = 1 for the vertical
thermal derating, …). For example, Fig. x.1 will refer
to the vertical thermal derating for all the output
voltages in general.
The following pages contain specific plots or
waveforms associated with the converter. Additional
comments for specific data are provided below.
Test Conditions
All data presented were taken with the converter
soldered to a test board, specifically a 0.060” thick
printed wiring board (PWB) with four layers. The top
and bottom layers were not metalized. The two inner
layers, comprised of two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that heat
transfer from the converter to the PWB was
minimized. This provides a worst-case but consistent
scenario for thermal derating purposes.
MCD10204 Rev. 1.0, 24-Jun-10
Page 7 of 30
www.power-one.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
YS05S16-0 CONVERT DC/DC 58W SMD
YS12S10-DG CONVERT DC/DC 55W SMD
YS12S16-0 CONVERT DC/DC 88W SMD
YV12T25-0 CONVERT DC/DC 137W T/H
ZA5350-B CLIP TERM W/8"CORD BARE
ZA5350 CLIP TERM W/8"CORD & DC PLUG
ZCAT12V-BK FILTER CABLE/CLAMP 140 OHM 12MM
ZCAT6819-5230D-BK FILTER CABLE/CLAMP 35 OHM 40COND
相关代理商/技术参数
YS05S10-0G 功能描述:DC/DC转换器 0.7525-3.63Vout 10A 3-5.5VIn RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
YS05S10-DG 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
YS05S16-0 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
YS05S16-0G 功能描述:DC/DC转换器 0.7525-3.63Vout 16A 3-5.5VIn RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
YS05S16-DG 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
YS-1 制造商:Taiyo Electric Ind. 功能描述:
YS10 制造商:Norma Products Midlands 功能描述:10MM ID HOSE Y CONNECTOR
YS-100 制造商:Taiyo Electric Ind. 功能描述: